East Wind Tractors and Dozers - How to fit tractor implements to your 3 point linkage, power take off PTO and hydraulic connections. Information on connecting, adjusting and safety when using tractor implements with small to medium sized tractors and dozers on small acrage and hobby farms in Australia. Including, building a bike track, maintaining or repairing a driveway, log splitting, digging trenches and laying irrigation pipe, building a bush shed, building an entrance fence and gate and many more useful tips to make the most out of your small acreage tractor or dozer. Sales in Brisbane, Queensland, sunshine coast, north, south, east, west, gold coast, central, rockhampton, sydney, new south wales, newcastle, melbourne, victoria, canberra, albury, lismore, stanthorpe, ipswich, toowoomba, townsville, adelaide, perth, darwin, western, northern territory, coffs harbour and more. Tractors and dozers have 3-point linkage kits for a large range of implements including front end loader, backhoes. Australia wide distributors.

'How To Use' your Tractor or Dozer for Projects

Tractor Implement Fitting

The humble tractor is only as useful as the implements you attach to it. The ability to quickly and easily change implements makes the small acreage tractor far more versatile for the average hobby farmer. The following will show you how to make light work of changing implements.

Implement Types

Implements can be broken into three types:

3 point linkage (3 PL) connections. This is the most basic kind of connection and simply enables implements to be raised and lowered. Some examples would be a carry all, grader blade and a ripper.
Power take off (PTO) connections. This involves connecting to a rotating shaft on the tractor which drives implements such as a slasher, rotary hoe or posthole digger. PTO driven implements are usually also attached to the 3PL.
Hydraulic connections. This involves connecting a hydraulically driven implement to the tractor hydraulics using hoses and couplings. Some examples would be a wood splitter, tipping trailer and a backhoe.

Important General Information

When connecting and disconnecting implements it is best to work on firm level ground.
Implements are very heavy. Be careful in handling them to avoid personal injury. Dismantling implements into smaller parts can be done quickly and easily to make them easier to handle.
Some implements can be unstable while being disconnected or after they are disconnected. Always handle them carefully to avoid them tipping over.
Always leave the tractor in a safe state when getting off it to connect / disconnect / adjust implements - i.e. disengage the PTO, turn the engine off and apply the hand brake.
PTO shafts rotate very quickly and can cause severe injury due to entanglement. Never allow anyone to go near an operating PTO and ensure it is always correctly guarded.
Hydraulic systems operate under high pressure. Never attempt to connect or disconnect hydraulic fittings under pressure. Always turn the engine off when working with hydraulic connections.

Attach to tractor 3 point linkage arms

Attach top link to tractor

Some implements use a chain for the top link

Fine tune height adjustment with upright arms

Adjust side movement with sway chains

Ensure PTO guard and safety chain are in place

Set the high low limiter to prevent PTO damage

Hydraulic implements need a hydraulic connection

3PL connections

In this example we are using a grader blade but the same principals would apply to many implements. Start the tractor and reverse it towards the implement ensuring the tractor is square to the implement.

Raise or lower the height of the lower linkage arms to match the height of the implement mounting points using the tractor hydraulic 3PL control.

It may also be necessary to adjust the width between the two lower arms to accommodate the width of the implement. This is done by turning the sway chain adjusters to create more or less free play.

Slowly reverse the tractor so that the lower linkage arms fit into the implement mounting points. Attach the implement to the 3PL with mounting pins and secure with linch pins. A pry bar can be used to fine tune the position if you have difficulty aligning the linkage arm and implements.

Next attach the top link with mounting pins and linch pins. Some are rigid bars and some are chains. (The slasher below has a chain to allow the implement to pivot up if it hits a large bump / object. This helps protect the PTO shaft from damage).

The implement will now need to be adjusted. The hydraulic system will have a lift limiter adjuster to set how high or low the implement can be raised – this is particularly important with PTO driven implements - refer below. Height adjustment can be fine tuned by turning the upright arms.

Sway chain adjusters enable you to pull the implement in tight to the two bottom linkage arms and minimize sway. The linkage should be set up with some free play (approximately 50mm) to protect against damage from side forces.

PTO implements need a drive shaft connection

Power Take Off Connections

Note when fitting an implement for the first time, it is essential to ensure the implement PTO shaft is a suitable length. The implement PTO shaft is telescopic to allow it to vary in length as the implement is raised and lowered. If the shaft is too short it will come apart when the implement is lowered. If the shaft is too short it will need to be replaced with a longer one. If the shaft is too long the shaft can "bottom out". This can be rectified by cutting the shaft down. Refer to the implement instruction manual for getting the shaft length right.

Most PTO driven implements are first fitted to the 3PL as described above. The implement PTO shaft is then fitted to the tractor PTO drive shaft. Start by aligning the splines between the yolk and the tractor drive shaft. Then press the quick release button to slide the yolk on. Slide the yolk fully home until the quick release button pops out. Ensure the PTO guard is in place and the safety chain is attached.

Use the high low limiter to ensure the implement can't be raised high enough for the PTO shaft to hit the implement. Conduct the check with the PTO disengaged. If a turning shaft hits the implement it can cause damage to the PTO system or personal injury.

Hydraulic Connections

Many hydraulically driven implements such as a backhoe are also fitted to the 3PL.

These implements may use a more robust top link but the principal of connecting to the three points is the same. Once connected it is simply a matter of connecting the implement hydraulic hoses to the correct hydraulic connections on the tractor.

Safety is always the highest priority. Always use a tractor that complies with Australian Standards, including Roll Over Protective Structure, seat belt and protective covers. Only take on tasks within the capability of the machine and operator. Follow all relevant safety warnings, instructions and regulations. Wear appropriate safety equipment and use common sense.

* This article is a general guide only. Conditions vary from site to site. Judgement relating to your individual conditions must be exercised.

East Wind Tractors and Hanmey Implements feature in these article.
For more information visit www.eastwind.com.au or www.hanmey.com.au or call 1300 TRACTOR (1300 87 22 86).

Return to more 'How To' articles

East Wind supply useful information on how to correctly fit implements and attachments to your tractor or dozer. There is information on adjusting 3 point likage kit, attaching hydraulics and safety using the power take off (PTO).

Tractors and Dozers from East Wind are specially made for Australian farm conditions and have proven reliability in Australia for over 14 years. They are suited to a huge range of small to large implements for use around small acreage farms and hobby and lifestyle farms. Our range of small tractors, small to medium tractors, as well as large 55hp tractors for larger properties and 30hp dozers for all types of properties including hilly farms are located in Queensland, New South Wales, Victoria, South Australia, Western Australia, Tasmania, New Caledonia and new Zealand.

Tractors for sale in Australia from our branches in Queensland and Victoria include delivery to all areas of Brisbane, Cairns, Townsville, Gold Coast, Toowoomba, Maryborough, Barcaldine, Proserpine, Winton, Longreach, Mt. Isa, Mackay, Rockhampton, Charleville, Warwick, Cloncurry, Emerald, Roma, Miles, Normanton, Gladstone, Sunshine Coast, Cunnamulla and Goondiwindi in Queensland (QLD). In Victoria our tractor sales to Melbourne, Horsham, Ballarat, Colac, Portland, Morwell, Hamilton, Seymour, Bendigo, Mildura, Geelong, Shepparton, Wangaratta, Warnambool and Bairnsdale.

Our Dealers in Tasmania, Western Australia, New Zealand and New Caledonia are suppliers of small acreage tractors and dozers to Perth in Western Australia (WA) as well as Kalgoorlie, Mandurah, Halls, Creek, Kununarra, Armadale, Northam, Port Denison, Albany, Margaret River, Bunbury, Rockingham, Port Hedland, Headland, Broome, Geraldton, Esperance, Carnavon, Karratha, Monkey Mia, Morawa, Merredin, Eucla and many places in between. In Tasmania (TAS) there are tractors and dozers for sales to Launceston, Hobart, Burnie, Smithton, Bicheno, Beaconsfield, St. Helens, Saint Marys, Queenstown, Scottsdale, Kingston, Devonport, Orford and Oatlands.

If you are looking for information on servicing your tractor or looking for new farm tractors for sale or sales of compact dozers, contact East Wind today or drop into one of our Dealers and Distributors to see the full range of tractors and dozers, where we are sure you will find a tractor or dozer to suit your small acreage farm equipment needs.

^ top

East Wind Products

Service Network

Useful Information

Dealer Specials